MUET logo

Effect Of Porous Baffles On Fluid Flow And Heat Transfer In A BackwardStep Channel: Numerical Predictions

Authors

  • Rafique Ahmed Soomro

    Department of Mathematics, Shah Abdul Latif University, Khairpur, Sindh
    Author

  • Hisamuddin Shaikh

    Department of Mathematics, Shah Abdul Latif University, Khairpur, Sindh
    Author

DOI:

https://doi.org/10.22581/0660

Keywords:

Darcy Number, Porous Medium, Heat Transfer, COMSOL, Viscosity Ratio, Backward-facing Step Channel

Abstract

In this paper, numerical analysis is used to study coupled fluid flow and heat transfer in a backward-facing step channel with a porous baffle installed at its midpoint. This configuration is a canonical geometry for investigating passive heat-transfer enhancement in separated internal flows. Simulations are performed using COMSOL Multiphysics 6.0 and the finite element method to solve a four-field coupled system comprising the incompressible Navier–Stokes equations for laminar flow, the Darcy–Brinkman model for porous media, and the two-dimensional energy conservation equation for heat transfer. A comprehensive parametric study investigates the effects of Reynolds number (Re = 100–2000), Darcy number (Da = 0.001–0.1), and viscosity ratio (a = μporous/μwater = 3–7) on the velocity field, pressure distribution, and temperature profile at the channel outlet. The results show a linear increase in maximum outlet velocity with Reynolds number, consistent with the definition of Re and the fixed geometry. The laminar nature of the flow is confirmed through literature benchmarks and an unsteady sensitivity study. The maximum velocity is 0.167 m/s at Re = 2000, Da = 0.001, and a = 7; at the same Re and a, it decreases to 0.098 m/s when Da = 0.1. The inlet-to-outlet pressure drop (ΔP = Pin − Pout) increases nonlinearly with Re. At Da = 0.1 and a = 5, the pressure drop is approximately 0.49 Pa at Re = 2000, showing that form drag and flow separation depend strongly on permeability and geometry. The bulk outlet temperature decreases as Reynolds number increases because the higher mass flow rate distributes the fixed heat input over a greater mass of fluid. The total heat-transfer rate remains constant at 40.00 W/m, consistent with the fixed heat-flux boundary condition. At high Re, the maximum-temperature differences between Darcy numbers are approximately 0.15 K, close to the discretization uncertainty of 0.09 K. The findings show that smaller Darcy numbers and higher viscosity ratios enhance jetting and convective heat transfer, offering design guidance for porous-baffle heat-transfer devices such as compact heat exchangers and obstructed cooling channels. Thermal-hydraulic performance is evaluated using the average Nusselt number, pumping power, and performance evaluation criterion (PEC). The PEC ranges from 1.12 to 1.42, indicating that thermal enhancement exceeds the hydraulic penalty. The energy balance closes within 0.38% for all cases.

Downloads

Author Biographies

  • Rafique Ahmed Soomro, Department of Mathematics, Shah Abdul Latif University, Khairpur, Sindh

    Associate Professor BPS-19,  College Education Department Govt of Sindh 

  • Hisamuddin Shaikh, Department of Mathematics, Shah Abdul Latif University, Khairpur, Sindh

    Professor bps-21 and chairman Department of Mathematics 

References

[1] A. M. Norouzi, M. Siavashi, and M. K. Oskouei, “Efficiency enhancement of the parabolic trough solar collector using the rotating absorber tube and nanoparticles,” Renewable Energy, vol. 145, pp. 569–584, 2020.

[2] M. Siavashi, K. Ghasemi, R. Yousofvand, and S. Derakhshan, “Computational analysis of SWCNH nanofluid-based direct absorption solar collector with a metal sheet,” Solar Energy, vol. 170, pp. 252–262, 2018.

[3] M. Dehghan, Y. Rahmani, D. D. Ganji, S. Saedodin, M. S. Valipour, and S. Rashidi, “Convection– radiation heat transfer in solar heat exchangers filled with a porous medium: Homotopy perturbation method versus numerical analysis,” Renewable Energy, vol. 74, pp. 448–455, 2015.

[4] S. Li, J. Yuan, G. Xie, and B. Sunden, “Numerical investigation of transport phenomena in high temperature proton exchange membrane fuel cells with different flow field designs,” Numerical Heat Transfer, Part A: Applications, vol. 72, no. 11, pp. 807–820, 2017.

[5] H. Pourrahmani, M. Moghimi, and M. Siavashi, “Thermal management in PEMFCs: the respective effects of porous media in the gas flow channel,” International Journal of Hydrogen Energy, vol. 44, no. 5, pp. 3121–3137, 2019.

[6] M. H. Doranehgard and M. Siavashi, “The effect of temperature dependent relative permeability on heavy oil recovery during hot water injection process using streamline-based simulation,” Applied Thermal Engineering, vol. 129, pp. 106–116, 2018.

[7] M. Siavashi and M. H. Doranehgard, “Particle swarm optimization of thermal enhanced oil recovery from oilfields with temperature control,” Applied Thermal Engineering, vol. 123, pp. 658– 669, 2017.

[8] M. Siavashi, M. J. Blunt, M. Raisee, and P. Pourafshary, “Three-dimensional streamline-based simulation of non-isothermal two-phase flow in heterogeneous porous media,” Computers & Fluids, vol. 103, pp. 116–131, 2014.

[9] R. Yousofvand, S. Derakhshan, K. Ghasemi, and M. Siavashi, “MHD transverse mixed convection and entropy generation study of electromagnetic pump including a nanofluid using 3D LBM simulation,” International Journal of Mechanical Sciences, vol. 133, pp. 73–90, 2017.

[10] Q. Ren, Y.-L. He, K.-Z. Su, and C. L. Chan, “Investigation of the effect of metal foam characteristics on the PCM melting performance in a latent heat thermal energy storage unit by pore-scale lattice Boltzmann modeling,” Numerical Heat Transfer, Part A: Applications, vol. 72, no. 10, pp. 745–764, 2017.

[11] Y. Du and Y. Ding, “Towards improving charge/discharge rate of latent heat thermal energy storage (LHTES) by embedding metal foams in phase change materials (PCMs),” Chemical Engineering and Processing: Process Intensification, vol. 108, pp. 181–188, 2016.

[12] K. Ghasemi and M. Siavashi, “Three-dimensional analysis of magnetohydrodynamic transverse mixed convection of nanofluid inside a lid-driven enclosure using MRT-LBM,” International Journal of Mechanical Sciences, vol. 165, p. 105199, 2020.

[13] T. Alam and M.-H. Kim, “A comprehensive review on single phase heat transfer enhancement techniques in heat exchanger applications,” Renewable and Sustainable Energy Reviews, vol. 81, pp. 813–839, 2018.

[14] A. Al-Aswadi, H. Mohammed, N. Shuaib, and A. Campo, “Laminar forced convection flow over a backward facing step using nanofluids,” International Communications in Heat and Mass Transfer, vol. 37, no. 8, pp. 950–957, 2010.

[15] M. Siavashi, H. R. T. Bahrami, and E. Aminian, “Optimization of heat transfer enhancement and pumping power of a heat exchanger tube using nanofluid with gradient and multi-layered porous foams,” Applied Thermal Engineering, vol. 138, pp. 465–474, 2018.

[16] M. Siavashi and S. Iranmehr, “Using sharp wedge-shaped porous media in front and wake regions of external nanofluid flow over a bundle of cylinders,” International Journal of Numerical Methods for Heat & Fluid Flow, vol. 29, no. 10, pp. 3730–3755, 2019.

[17] O. Mahian, L. Kolsi, M. Amani, P. Estellé, G. Ahmadi, C. Kleinstreuer, J. S. Marshall, M. Siavashi, R. A. Taylor, H. Niazmand, S. Wongwises, T. Hayat, A. Kolanjiyil, A. Kasaeian, and I. Pop, “Recent advances in modeling and simulation of nanofluid flows-part i: Fundamentals and theory,” Physics Reports, vol. 790, pp. 1–48, 2019. Recent advances in modeling and simulation of nanofluid flows—Part I: Fundamentals and theory.

[18] M. Omid, K. Lioua, A. Mohammad, P. Estellé, G. Ahmadi, C. Kleinstreuer, and I. Pop, “Recent advances in modeling and simulation of nanofluid flows—part ii: Applications,” Phys. Rep, vol. 791, pp. 1–59, 2019.

[19] A. Amiri, H. K. Arzani, S. Kazi, B. Chew, and A. Badarudin, “Backward-facing step heat transfer of the turbulent regime for functionalized graphene nanoplatelets based water–ethylene glycol nanofluids,” International Journal of Heat and Mass Transfer, vol. 97, pp. 538–546, 2016.

[20] F. Selimefendigil and H. F. Öztop, “Laminar convective nanofluid flow over a backward-facing step with an elastic bottom wall,” Journal of Thermal Science and Engineering Applications, vol. 10, no. 4, p. 041003, 2018.

[21] H. Togun, M. R. Safaei, R. Sadri, S. N. Kazi, A. Badarudin, K. Hooman, and E. Sadeghinezhad, “Numerical simulation of laminar to turbulent nanofluid flow and heat transfer over a backward-facing step,” Applied Mathematics and Computation, vol. 239, pp. 153–170, 2014.

[22] F. Selimefendigil and H. F. Öztop, “Identification of forced convection in pulsating flow at a backward facing step with a stationary cylinder subjected to nanofluid,” International Communications in Heat and Mass Transfer, vol. 45, pp. 111–121, 2013.

[23] A. K. Hilo, A. A. Iborra, M. T. H. Sultan, and M. F. A. Hamid, “Effect of corrugated wall combined with backward-facing step channel on fluid flow and heat transfer,” Energy, vol. 190, p. 116294, 2020.

[24] Y.-L. Tsay, T.-S. Chang, and J.-C. Cheng, “Heat transfer enhancement of backward-facing step flow in a channel by using baffle installation on the channel wall,” Acta Mechanica, vol. 174, no. 1, pp. 63–76, 2005.

[25] A. Heshmati, H. A. Mohammed, and A. N. Darus, “Mixed convection heat transfer of nanofluids over backward facing step having a slotted baffle,” Applied Mathematics and Computation, vol. 240, pp. 368–386, 2014.

[26] M. Siavashi, H. Rasam, and A. Izadi, “Similarity solution of air and nanofluid impingement cooling of a cylindrical porous heat sink,” Journal of Thermal Analysis and Calorimetry, vol. 135, no. 2, pp. 1399–1415, 2019.

[27] P. Maghsoudi and M. Siavashi, “Application of nanofluid and optimization of pore size arrangement of heterogeneous porous media to enhance mixed convection inside a two-sided lid-driven cavity,” Journal of Thermal Analysis and Calorimetry, vol. 135, no. 2, pp. 947–961, 2019.

[28] M. Ramezanpour and M. Siavashi, “Application of SiO2–water nanofluid to enhance oil recovery: A new hybrid optimization approach using pattern search and PSO algorithms,” Journal of Thermal Analysis and Calorimetry, vol. 135, no. 1, pp. 565– 580, 2019.

[29] M. Siavashi, K. Karimi, Q. Xiong, and M. H. Doranehgard, “Numerical analysis of mixed convection of two-phase non-Newtonian nanofluid flow inside a partially porous square enclosure with a rotating cylinder,” Journal of Thermal Analysis and Calorimetry, vol. 137, no. 1, pp. 267–287, 2019.

[30] A. Izadi, M. Siavashi, and Q. Xiong, “Impingement jet hydrogen, air and CuH2O nanofluid cooling of a hot surface covered by porous media with non-uniform input jet velocity,” International Journal of Hydrogen Energy, vol. 44, no. 30, pp. 15933– 15948, 2019.

[31] A. Izadi, M. Siavashi, H. Rasam, and Q. Xiong, “MHD enhanced nanofluid mediated heat transfer in porous metal for CPU cooling,” Applied Thermal Engineering, vol. 168, p. 114843, 2020.

[32] I. Zahmatkesh and S. Ali Naghedifar, “Oscillatory mixed convection in the jet impingement cooling of a horizontal surface immersed in a nanofluid-saturated porous medium,” Numerical Heat Transfer, Part A: Applications, vol. 72, no. 5, pp. 401–416, 2017.

[33] H. Pourrahmani, M. Moghimi, M. Siavashi, and M. Shirbani, “Sensitivity analysis and performance evaluation of the PEMFC using wave-like porous ribs,” Applied Thermal Engineering, vol. 150, pp. 433–444, 2019.

[34] H. Pourrahmani, M. Siavashi, and M. Moghimi, “Design optimization and thermal management of the PEMFC using artificial neural networks,” Energy, vol. 182, pp. 443–459, 2019.

[35] M. H. Toosi and M. Siavashi, “Two-phase mixture numerical simulation of natural convection of nanofluid flow in a cavity partially filled with porous media to enhance heat transfer,” Journal of Molecular Liquids, vol. 238, pp. 553–569, 2017.

[36] S. M. Miri Joibary and M. Siavashi, “Effect of Reynolds asymmetry and use of porous media in the counterflow double-pipe heat exchanger for passive heat transfer enhancement,” Journal of Thermal Analysis and Calorimetry, vol. 140, no. 3, pp. 1079–1093, 2020.

[37] M. Siavashi and S. M. Miri Joibary, “Numerical performance analysis of a counter-flow double-pipe heat exchanger with using nanofluid and both sides partly filled with porous media,” Journal of Thermal Analysis and Calorimetry, vol. 135, no. 2, pp. 1595–1610, 2019.

[38] P. Gholamalipour, M. Siavashi, and M. H. Doranehgard, “Eccentricity effects of heat source inside a porous annulus on the natural convection heat transfer and entropy generation of Cu-water nanofluid,” International Communications in Heat and Mass Transfer, vol. 109, p. 104367, 2019.

[39] S. Mousavi, M. Siavashi, and M. M. Heyhat, “Numerical melting performance analysis of a cylindrical thermal energy storage unit using nano-enhanced PCM and multiple horizontal fins,” Numerical Heat Transfer, Part A: Applications, vol. 75, no. 8, pp. 560–577, 2019.

[40] M. Siavashi, H. R. T. Bahrami, and H. Saffari, “Numerical investigation of flow characteristics, heat transfer and entropy generation of nanofluid flow inside an annular pipe partially or completely filled with porous media using two-phase mixture model,” Energy, vol. 93, pp. 2451–2466, 2015.

[41] X. Chen, P. Yu, S. Winoto, and H. Low, “Forced convection over a backward-facing step with a porous floor segment,” Numerical Heat Transfer, Part A: Applications, vol. 53, no. 11, pp. 1211– 1230, 2008.

[42] B. Abu-Hijleh, “Convection heat transfer from a laminar flow over a 2-D backward facing step with asymmetric and orthotropic porous floor segments,” Numerical Heat Transfer, Part A: Applications, vol. 31, no. 3, pp. 325–335, 1997.

[43] B. A. K. Abu-Hijleh, “Heat transfer from a 2D backward facing step with isotropic porous floor segments,” International Journal of Heat and Mass Transfer, vol. 43, no. 15, pp. 2727–2737, 2000.

[44] M. J. de Lemos and W. C. Galuppo, “Effect of porous insert on heat transfer in a backward-facing step flow,” in Heat Transfer Summer Conference, vol. 50329, p. V001T05A011, American Society of Mechanical Engineers, 2016.

[45] S. Kimura, S.-I. Nakao, and S.-I. Shimatani, “Transport phenomena in membrane distillation,” Journal of Membrane Science, vol. 33, no. 3, pp. 285–298, 1987.

[46] R. K. Shah, A. L. London, T. F. Irvine, and J. P. Hartnett, Laminar Flow Forced Convection in Ducts. Elsevier, 1978.

[47] E. Erturk, “Numerical solutions of 2-D steady incompressible flow over a backward-facing step, Part I: High Reynolds number solutions,” Computers & Fluids, vol. 37, no. 6, pp. 633–655, 2008.

[48] D. Kumar Maiti and R. Bhatt, “Vortex shedding suppression and aerodynamic characteristics of square cylinder due to offsetting of rectangular cylinders towards a plane,” Ocean Engineering, vol. 82, pp. 91–104, 2014.

[49] T. C. Jue, “Numerical analysis of vortex shedding behind a porous square cylinder,” International Journal of Numerical Methods for Heat & Fluid Flow, vol. 14, no. 5, pp. 649–663, 2004.

[50] P. J. Roache, “Perspective: A method for uniform reporting of grid refinement studies,” Journal of Fluids Engineering, vol. 116, no. 3, pp. 405–413, 1994.

[51] B. F. Armaly, F. Durst, J. Pereira, and B. Schönung, “Experimental and theoretical investigation of backward-facing step flow,” Journal of Fluid Mechanics, vol. 127, pp. 473–496, 1983.

[52] D. K. Gartling, “A test problem for outflow boundary conditions—flow over a backward-facing step,” International Journal for Numerical Methods in Fluids, vol. 11, no. 7, pp. 953–967, 1990.

Published

2026-10-01

Issue

Vol. 45 No. 4 (2026): October Issue

Section

Articles

License

Copyright (c) 2026 Mehran University Research Journal of Engineering and Technology

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

How to Cite

Effect Of Porous Baffles On Fluid Flow And Heat Transfer In A BackwardStep Channel: Numerical Predictions. (2026). Mehran University Research Journal of Engineering and Technology, 45(4), 92-111. https://doi.org/10.22581/0660

Similar Articles

41-48 of 48

You may also start an advanced similarity search for this article.