MUET logo

Experimental Investigation of Constituent Materials for Multilayered Impact Resistant Panels: Fiber-Reinforced Ceramic, Shape Memory Alloy, and  Titanium Alloy Lattice Structures

Authors

  • Muhammad Abid

    Department of Mechanical Engineering, Faculty of Engineering, Islamic University of Madinah, Madinah, Saudi Arabia, KSA
    Author

  • Haris Khalid

    Department of Mechanical Engineering, Faculty of Engineering, Islamic University of Madinah, Madinah, Saudi Arabia, KSA
    Author

  • Hafiz Abdul Wajid

    Department of Electrical Engineering, Faculty of Engineering, Islamic University of Madinah, Madinah, Saudi Arabia, KSA
    Author

  • Uzair Ahmad Dar

    Centres of Excellence in Science and Applied Technologies (CESAT), Islamabad, Pakistan
    Author

DOI:

https://doi.org/10.22581/0789

Keywords:

Selective Laser Melting (SLM), Fiber-Reinforced Ceramic (FRC), Shape Memory Alloy (SMA), Lattice Structures, Heat Treatment, Energy Absorption

Abstract

This experimental study investigates the mechanical performance and energy absorption characteristics of materials for a newly developed multilayered impact-resistant panel. The proposed lightweight structure combines fiber-reinforced ceramic (FRC), nickel-titanium shape memory alloy (SMA), and additively manufactured Ti-6Al-4V lattice structures in uniform body-centered cubic (UBCC) and vertical-strut (UBCCz) configurations. Each material was fabricated, heat-treated under controlled conditions, and mechanically tested to assess its suitability for impact-resistant applications. The FRC panels exhibited a compressive strength of 50 MPa and a fracture toughness of 2.8 MPa·m¹ᐟ², supporting their use as a strike-face layer. Heat treatment of the SMA at 700 °C for 30 minutes increased energy absorption by 21% and failure strain by 40%, while reducing tensile strength. For both UBCC and UBCCz Ti-6Al-4V lattice structures, non-heat-treated samples demonstrated superior compressive properties compared with heat-treated samples. Increasing the UBCCz strut diameter from 1 mm to 2 mm substantially improved compressive strength and energy absorption. The experimental results for the multilayered panel were in good agreement with numerical simulation results reported in the literature. At an impact velocity of 100 m/s, the panel distributed the impact energy across its layers: 21% was absorbed by the FRC, 28% by the SMA, and 50% by the titanium lattice, while the aluminum backing contributed minimally. Multilayered impact-resistant panels with the same sequence of material layers were physically fabricated. Further impact testing is recommended to evaluate the panels’ damage and energy absorption behavior.

Downloads

References

[1] R. A. W. Mines, S. Tsopanos, Y. Shen, R. Hasan, and S. T. McKown, “Drop weight impact behaviour of sandwich panels with metallic micro lattice cores,” International Journal of Impact Engineering, vol. 60, pp. 120–132, 2013.

[2] A. Herrmann, P. Zahlen, and I. Zuardy, “Sandwich structures technology in commercial aviation,” Sandwich Structures 7: Advancing with Sandwich Structures and Materials, pp. 13–26, 2005.

[3] D. T. Queheillalt and H. N. Wadley, “Titanium alloy lattice truss structures,” Materials & Design, vol. 30, no. 6, pp. 1966–1975, 2009.

[4] M. Z. Mahmoudabadi and M. Sadighi, “A theoretical and experimental study on metal hexagonal honeycomb crushing under quasi-static and low velocity impact loading,” Materials Science and Engineering: A, vol. 528, no. 15, pp. 4958–4966, 2011.

[5] R. Rahmani, M. Antonov, and M. Brojan, “Lightweight 3D printed Ti6Al4V-AlSi10Mg hybrid composite for impact resistance and armor piercing shielding,” Journal of Materials Research and Technology, vol. 9, no. 6, pp. 13842–13854, 2020.

[6] L. Xiao, W. Song, and X. Xu, “Experimental study on the collapse behavior of graded Ti-6Al-4V micro-lattice structures printed by selective laser melting under high speed impact,” Thin-Walled Structures, vol. 155, 2020. Art. no. 106970.

[7] P. Y. Li, Y. E. Ma, and W. B. Sun, “Low velocity impact response of additive manufacturing TI6AL-4V sandwich panels with lattice,” in 22nd International Conference on Composite Materials, pp. 3396–3404, 2019.

[8] K. A. Tsoi, R. Stalmans, J. Schrooten, M. Wevers, and Y. W. Mai, “Impact damage behaviour of shape memory alloy composites,” Materials Science and Engineering: A, vol. 342, no. 1-2, pp. 207–215, 2003.

[9] M. Meo, F. Marulo, M. Guida, and S. Russo, “Shape memory alloy hybrid composites for improved impact properties for aeronautical applications,” Composite Structures, vol. 95, pp. 756–766, 2013.

[10] M. Guida, A. Sellitto, F. Marulo, and A. Riccio, “Analysis of the impact dynamics of shape memory alloy hybrid composites for advanced applications,” Materials, vol. 12, no. 1, 2019. Art. no. 153.

[11] R. Vrána, D. Koutný, D. Paloušek, O. Koukal, T. Zikmund, and P. Krejčí, “Impact resistance of lattice structure made by selective laser melting technology,” in Proceedings of Euro PM, 2015.

[12] C. J. Yungwirth, J. O’Connor, A. Zakraysek, V. S. Deshpande, and H. N. Wadley, “Explorations of hybrid sandwich panel concepts for projectile impact mitigation,” Journal of the American Ceramic Society, vol. 94, pp. s62–s75, 2011.

[13] M. Sun, Z. Wang, B. Yang, and X. Sun, “Experimental investigation of GF/epoxy laminates with different SMAs positions subjected to lowvelocity impact,” Composite Structures, vol. 171, pp. 170–184, 2017.

[14] F. Pinto and M. Meo, “Mechanical response of shape memory alloy–based hybrid composite subjected to low-velocity impacts,” Journal of Composite Materials, vol. 49, no. 22, pp. 2713–2722, 2015.

[15] M. L. McMillan, M. Jurg, M. Leary, and M. Brandt, “Programmatic generation of computationally efficient lattice structures for additive manufacture,” Rapid Prototyping Journal, vol. 23, no. 3, pp. 486– 494, 2017.

[16] J. Brennan-Craddock, D. Brackett, R. Wildman, and R. Hague, “The design of impact absorbing structures for additive manufacture,” Journal of Physics: Conference Series, vol. 382, no. 1, 2012. Art. no. 012042.

[17] T. Maconachie, M. Leary, B. Lozanovski, X. Zhang, M. Qian, O. Faruque, and M. Brandt, “SLM lattice structures: Properties, performance, applications and challenges,” Materials & Design, vol. 183, 2019. Art. no. 108137.

[18] C. G. Ferro, S. Varetti, G. De Pasquale, and P. Maggiore, “Lattice structured impact absorber with embedded anti-icing system for aircraft wings fabricated with additive SLM process,” Materials Today Communications, vol. 15, pp. 185–189, 2018.

[19] M. G. Rashed, M. Ashraf, R. A. W. Mines, and P. J. Hazell, “Metallic microlattice materials: A current state of the art on manufacturing, mechanical properties and applications,” Materials & Design, vol. 95, pp. 518–533, 2016.

[20] R. Hasan, R. Mines, and P. Fox, “Characterization of selectively laser melted Ti-6Al-4 V micro-lattice struts,” Procedia Engineering, vol. 10, pp. 536– 541, 2011.

[21] S. Heimbs, J. Cichosz, M. Klaus, S. Kilchert, and A. F. Johnson, “Sandwich structures with textile-reinforced composite foldcores under impact loads,” Composite Structures, vol. 92, no. 6, pp. 1485–1497, 2010.

[22] B. Song, S. Dong, B. Zhang, H. Liao, and C. Coddet, “Effects of processing parameters on microstructure and mechanical property of selective laser melted Ti6Al4V,” Materials & Design, vol. 35, pp. 120–125, 2012.

[23] C. Yan, L. Hao, A. Hussein, and D. Raymont, “Evaluations of cellular lattice structures manufactured using selective laser melting,” International Journal of Machine Tools and Manufacture, vol. 62, pp. 32–38, 2012.

[24] J. A. Harris, R. E. Winter, and G. J. McShane, “Impact response of additively manufactured metallic hybrid lattice materials,” International Journal of Impact Engineering, vol. 104, pp. 177–191, 2017.

[25] I. Ullah, J. Elambasseril, M. Brandt, and S. Feih, “Performance of bio-inspired Kagome truss core structures under compression and shear loading,” Composite Structures, vol. 118, pp. 294–302, 2014.

[26] G. Labeas and E. Ptochos, “Homogenization of selective laser melting cellular material for impact performance simulation,” International Journal of Structural Integrity, vol. 6, no. 4, pp. 439–450, 2015.

[27] N. Jin, F. Wang, Y. Wang, B. Zhang, H. Cheng, and H. Zhang, “Failure and energy absorption characteristics of four lattice structures under dynamic loading,” Materials & Design, vol. 169, 2019. Art. no. 107655.

[28] C. Li, H. Lei, Y. Liu, X. Zhang, J. Xiong, H. Zhou, and D. Fang, “Crushing behavior of multi-layer metal lattice panel fabricated by selective laser melting,” International Journal of Mechanical Sciences, vol. 145, pp. 389–399, 2018.

[29] Y. Wang, F. Liu, X. Zhang, K. Zhang, X. Wang, D. Gan, and B. Yang, “Cell-size graded sandwich enhances additive manufacturing fidelity and energy absorption,” International Journal of Mechanical Sciences, vol. 211, 2021. Art. no. 106798.

[30] A. Fadeel, A. Mian, M. Al Rifaie, and R. Srinivasan, “Effect of vertical strut arrangements on compression characteristics of 3D printed polymer lattice structures: experimental and computational study,” Journal of Materials Engineering and Performance, vol. 28, no. 2, pp. 709–716, 2019.

[31] G. Labeas and E. Ptochos, “Investigation of sandwich structures with innovative cellular metallic cores under low velocity impact loading,” Plastics, Rubber and Composites, vol. 42, no. 5, pp. 194– 202, 2013.

[32] E. Ptochos and G. Labeas, “Elastic modulus and Poisson’s ratio determination of micro-lattice cellular structures by analytical, numerical and homogenization methods,” Journal of Sandwich Structures & Materials, vol. 14, no. 5, pp. 597–626, 2012.

[33] H. Li, K. Liu, Z. Tao, L. Ye, and W. Xiao, “The repeated low-velocity impact response and damage accumulation of shape memory alloy hybrid composite laminates,” e-Polymers, vol. 24, no. 1, 2024. Art. no. 20240100.

[34] H. Liu, G. Cai, K. Peng, H. Jin, and A. Alexander, “Thermal Behavior and Mechanical Properties of Different Lattice Structures Fabricated Using Selective Laser Melting,” Materials, vol. 17, no. 22, 2024. Art. no. 5603.

[35] H. Khalid, U. A. Dar, M. Abid, R. A. Pasha, and M. Bilal, “Numerical investigation of 3D printed multi-layered resistant hybrid panels under impact loading,” in 4th Pak-Turk International Conference on Emerging Technologies, 03–04 Nov. 2021.

[36] Z. Wei, T. Yu, and Y. An, “Research progress on impact resistance properties of fiber-reinforced ceramic matrix composites,” Journal of Physics: Conference Series, vol. 3080, no. 1, 2025. Art. no. 012131.

[37] S. Ge and Z. Wang, “Performance analysis of the energy absorbing box of Ni-Ti shape memory alloy under low-speed collision,” Journal of Physics: Conference Series, vol. 3043, no. 1, 2025. Art. no. 012063.

[38] M. Casata, S. Perosanz, T. Tang, T. Wilkinson, R. C. Reed, and D. Barba, “Evaluation of the size and orientation-dependent mechanical properties of additively manufactured Ti-6Al-4V: The role of microstructure, defects, and surface roughness and its implications for lattice structures,” Results in Engineering, vol. 27, 2025. Art. no. 106781.

[39] S. Ahmad, S. Zeb, Y. Wang, and M. Umair, “Blast Performance of Multi-Layer Composite Door Panel with Energy Absorption Connectors,” Buildings, vol. 15, no. 12, 2025. Art. no. 2073.

Published

2026-10-01

Issue

Vol. 45 No. 4 (2026): October Issue

Section

Articles

License

Copyright (c) 2026 Mehran University Research Journal of Engineering and Technology

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

How to Cite

Experimental Investigation of Constituent Materials for Multilayered Impact Resistant Panels: Fiber-Reinforced Ceramic, Shape Memory Alloy, and  Titanium Alloy Lattice Structures. (2026). Mehran University Research Journal of Engineering and Technology, 45(4), 138-147. https://doi.org/10.22581/0789

Similar Articles

31-40 of 55

You may also start an advanced similarity search for this article.